人的记忆力会随着岁月的流逝而衰退，写作可以弥补记忆的不足，将曾经的人生经历和感悟记录下来，也便于保存一份美好的回忆。相信许多人会觉得范文很难写？下面是小编帮大家整理的优质范文，仅供参考，大家一起来看看吧。
塔吊故障原因分析篇一
北京丹华昊博电力科技有限公司 配电线路是电力输送的终端，是电力系统的重要组成部分。配电线路点多线长面广，走径复杂，设备质量参差不齐，运行环境较为复杂，受气候或地理的环境影响较 大，并且直接面对用户端，供用电情况复杂，这些都直接或间接影响着配电线路的安全运行。配电线路设备故障率居高不下，故障原因远比输电线路复杂。
一、常见故障类型。a、人为因素造成的故障。
1、驾驶员违章驾驶引起的车辆撞到电杆，造成倒杆、断杆等事故发生；
2、基建或市政施工对配网造成破坏：一是基面开挖伤及地下敷设电缆；二是施工机械、物料超高超长碰触带电部位或破坏杆塔；
3、部分违章建筑物直接威胁线路的安全运行；
4、导线悬挂异物类：“庆典礼炮”和彩带、风筝、漂浮塑料；
5、动物危害：鼠、猫、蛇等动物爬到配电变压器上造成相间短路；
6、盗窃引发的倒杆、倒塔等重大恶性事故。
b、自然灾害造成的故障。通常是指雷击事故。因为架空10kv线路的路径较长，沿涂地形较空旷，附近少有高大建筑物，所以在每年的雷季中常遭雷击，由此产生的事故是10kv架空线路最常见的。其现象有绝缘子击穿或爆裂、断线、避雷器爆裂、配变烧毁等。
c、树木造成的故障。刮风下雨，极易造成导线对树木放电或树枝断落后搭在线上，风雨较大时，甚至会发生整棵树倒在线路上，压迫或压断导线，引发线路事
故。
d、配电设备方面的因素。
1、配电变压器故障。由于配电变压器本身故障或操作不当引起弧光短路；
2、绝缘子破裂，导致接地或绝缘子脏污导致闪络、放电、绝缘电阻降低，跳线烧断搭到铁担上；
3、避雷器、跌落保险、柱上开关质量较低或运行时间较长未能定期进行校验或更换，击穿后形成线路停电事故；
4、原有的户外柱上油开关是落后的旧设备，易出故障。
5、管理方面的因素。
二、故障原因分析。
a、线路设备老化严重，因种种原因发生故障的，气候突变时尤为严重。配电线路的一般情况是线径长，分支多，线路未改造，设备老化严重，因线路走廊的清障工 作未作彻底，违章建筑，树害，山田建设造成导线对地距离不够，低值、零值绝缘子较多，避雷器坏的也较多，导线松弛，弧垂过大，导线混线等原因，都有可能引 起线路故障，因此故障率居高不下。
1、导线断线故障：易断铝绞线；导线与绝缘子的绑扎处、引流绑扎处扎线脱落；交跨距离不够；
2、配电变台故障：跌落烧毁、配变烧毁、引流断等；
3、变压器避雷器损坏；
4、相间短路故障：线路档距过大，导线弧垂过大，大风时易混线，造成相间短路故障
5、低值、零值绝缘子造成故障；
6、保护定值不准；
7、电缆头爆炸引起故障；
8、私自操作设备引发故障：村民私自操作台变跌落熔丝具；或在跌落熔丝具触头上私自缠绕铁丝代替熔丝；
9、各类交跨距离不够引起线路故障：因l0kv线路面向用户端，线路通道远比输电网复杂，交跨各类高压线路、弱电线路、道路、建筑物、构筑物、堆积物等较多，极易引发线路故障的；
10、偷盗线路设备，盗割导线等造成线路停运；
11、车辆撞断电杆引起线路停运；
12、树障：树障是引起线路跳闸的一个重要原因，尤其在大风大雨天；
13、窃电造成短路跳闸：有的线路用户窃电较严重，而用户窃电一般是用裸金属线直接搭接在运行的裸导线上，有可能造成相间短路故障跳闸；
14、其它原因不明的故障。文章来源：故障定位
塔吊故障原因分析篇二
塔吊故障原因分析
塔吊从组装以来，大小故障一直不断，从而直接影响到工程施工进度，使工程无法正常运转，工期一再顺延，造成甲方对项目部有一种负面影响。
1、塔吊从4月7号开始组装，8号顶升，液压装置损坏，维修了两天，到9号下午16.20才结束。
2、旋转、小车接触器先后烧坏三只。
3、塔吊标准节有与标准节之间有误差，不配套有异常响声。
4、4月22号夜里小车钢丝绳滑槽，第二天停了2个多小时。5、4月24号上午小车钢丝绳再次滑槽，上午又停了2个多小时。
6、4月24号夜里2.00左右，吊截桩垃圾时，小车钢丝绳突然断裂，塔吊今天停止作业维修，工地处于停工状态。
该塔吊到目前为止，没有生产厂家的各项检测报告和后配加强节报告。针对这次小车钢丝绳断裂的问题，作如下分析：
1、4月22号夜里小车钢丝绳滑槽，是主要原因，因为这次滑槽，维修时，操作人员先把小车开到前面去，把前面的夹具松开，把钢丝绳子放入滑轮中，然后把小车开到后面来紧小车钢丝绳，这样钢丝绳就不在滚筒中间了。2、4月24号上午小车钢丝绳再次滑槽时，维修时，操作人员用同样的操作方法把钢丝绳放入槽中，这样小车钢丝绳就再一次地跑到一边来了，操作时，小车向前去的时候，滚筒上的钢丝绳就到一边了，因为滚筒上的钢丝绳进出是同步进行的，前面出、后面进，当钢丝绳紧到一边时，前面面没有位子，后面的还继续向上绕，这样钢丝绳就乱了，再加上小车来回行走，随着时间和操作次数的增加，就造成了钢丝绳的断裂。听指挥人员与操作人员说小车卡住了，前面有3米远就跑不去了，这就证明分析是对的。
塔吊故障原因分析篇三
汽车行驶时经常会遇到漏油的现象，靓/车/会告诉你应该如何检查发动机是否漏机油
汽车机油漏油主要是三方面漏油：发动机润滑系统漏油、油底垫漏油、气门室漏油。
1.发动机机体漏油主要是两方面：前曲轴油封漏油和后曲轴油封漏油，前曲轴油封漏油的位置是在发动机箱的前面漏油，后曲轴油封漏油的位置是在发动机后面漏油。漏机油有呈片状和点状，片状说明机器已经老化，需要更换机器零件，点状说明机器开始老化，需要去维修和护理。
2.油底垫漏油：目测观察发动机后部是否漏油。造成漏油的原因主要有：机器零件老化;维修后密封不严。
3.气门室漏油：目测观察汽车内部的机器漏油的地方是否渗油，从气门室盖去观测，它的位置是在发动机的最上方，观察是否浑浊渗透，如有污渍，说明你的爱车已经渗油了。造成漏油的原因：机器零件老化;机器密封不严。
另外新买的汽车，近期在跑高速的时候，感觉到漏风，应如何解决?
车速过高时漏风这个现象主要与车门密封条有关，其次检查线束经过的地方是否密封不良;漏风与车门密封条会有一定关系，您可以到汽配城内加装密封条，加装密封条的费用很低，每个车门大概在50元左右。汽车使用了一年多了，但是近来发现cvt加油有些迟缓，请问这是什么原因造成的?
此种故障和进气系统、燃油系统清洗关系不大。而从车辆使用率来分析，车辆利用率应该不高，也就是车辆每天行驶的车速和公里数不多，而根据发动机控制单元程序设定来讲，此种情况建议适当拉拉高速，将会有良好的效果改善，对于积碳清洁都是有一定帮助的。
塔吊故障原因分析篇四
xx月xx日xxxkvxxx线路故障跳闸原因分析报告(模板)1 线路概况
1.1 简介（电压等级、线路名称、线路变更情况、线路长度、杆塔数、海拔、地形、地质、建设日期、投运日期、资产单位、建设单位、设计单位、施工单位、运行单位）1.2设计气象条件 1.3 故障点基本参数 1.3.1杆、塔型。
1.3.2导、地线型号。
1.3.3 绝缘子（生产厂家、生产日期、绝缘子型式、外绝缘配置）。
1.3.4基础及接地。1.3.5线路相序。
1.3.6线路通道内外部环境描述。保护动作情况
保护动作描述、重合闸动作情况、保护测距情况、重合不成功强送电情况、抢修恢复时间。故障情况
3.1 根据保护测距计算的故障点 3.2 现场实际发现的故障情况 3.3 现场测试情况 故障原因分析 4.1近期运检情况
4.2 气象分析故障（当日天气情况)4.3 故障点地形、地貌
4.4 测试分析（雷电定位、接地电阻测量、绝缘子检测、绝缘子盐密和灰密（绝缘子污秽程度）、复合绝缘子憎水性、绝缘试验情况、在线监测等）
4.5设计校验（故障点基本参数、绝缘配置、防雷保护角、鸟刺加装、弧垂风偏校验）4.6现场走访情况（向故障点周边群众了解故障当时的天气、外部环境变化、异响、弧光等）
4.7其它故障排除情况（故障排除法）故障分析结论 暴露的问题 7 防范措施 7.1 已采取措施
7.2 拟采取措施(具体措施、措施落实责任人、措施落实时限)
附件一：现场故障现象（故障周边环境、故障点受损部件、引发故障的外部物件）图片 附件二：现场故障测试图片 附件三：现场故障处理图片
附件四：相关资质单位的试验鉴定报告 附件五：保护动作及故障录波参数 附件六：参加故障分析人员名单
单位： 日期：
塔吊故障原因分析篇五
0x00000000 0x00000000 0x00000000 nt_status_ok“操作成功完成。” 1 0xc0000001 0x0000001f 0x001f0001 nt_status_unsuccessful“附加到系统上的设备没有发挥作用。” 0xc0000002 0x00000001 0x00010001 nt_status_not_implemented“功能错误。” 0xc0000003 0x00000057 0x00570001 nt_status_invalid_info_class“的参数是不正确的。”
0 0xc0000004 0x00000018 0x00180001 nt_status_info_length_mismatch“程序发出命令，但命令长度不正确。”
0 0xc0000005 0x000003e6 0x03e60001 nt_status_access_violation“无效存取记忆体的位置。”
0 0xc0000006 0x000003e7 0x03e70001 nt_status_in_page_error“错误inpage操作表演。” 0 0xc0000007 0x000005ae 0x05ae0001 nt_status_pagefile_quota“配额不足，无法完成请求的服务。” 0xc0000008 0x00000006 0x00060001 nt_status_invalid_handle“句柄无效。”
0 0xc0000009 0x000003e9 0x03e90001 nt_status_bad_initial_stack“递归太深，堆栈溢出。”
0 0xc000000a 0x000000c1 0x00c10001 nt_status_bad_initial_pc“不是有效的windows nt应用程序。”
0 0xc000000b 0x00000057 0x00570001 nt_status_invalid_cid“的参数是不正确的。”
0 0xc000000c 0x0000013d 0x001f0003 nt_status_timer_not_canceled“nt_status_timer_not_canceled”
0 0xc000000d 0x00000057 0x00570001 nt_status_invalid_parameter“的参数是不正确的。”
0 0xc000000e 0x00000002 0x00020001 nt_status_no_such_device“系统找不到指定的文件。” 0xc000000f 0x00000002 0x00020001 nt_status_no_such_file“系统找不到指定的文件。” 0 0xc0000010 0x00000001 0x00010001 nt_status_invalid_device_request“不正确的函数。”
0 0xc0000011 0x00000026 0x00260001 nt_status_end_of_file“达到了文件的末尾。”
0 0xc0000012 0x00000022 0x00220001 nt_status_wrong_volume“错误的软盘驱动器中插入％2。（卷序列号：％3）插入驱动器％1。”
0 0xc0000013 0x00000015 0x00150001 nt_status_no_media_in_device“的设备没有准备好。”
0 0xc0000014 0x000006f9 0x06f90001 nt_status_unrecognized_media“磁盘媒体无法识别。它可能不会被格式化。”
0 0xc0000015 0x0000001b 0x001b0001 nt_status_nonexistent_sector“驱动器无法找到该部门的要求。” 0 0xc0000016 0x000000ea 0x00ea0001 nt_status_more_processing_required“更多的资料。”
0 0xc0000017 0x00000008 0x00080001 nt_status_no_memory“没有足够的存储是可用来处理此命令。”
0 0xc0000018 0x000001e7 0x01e70001 nt_status_conflicting_addresses“试图访问无效的地址。”
0 0xc0000019 0x000001e7 0x01e70001 nt_status_not_mapped_view“试图访问无效的地址。”
0 0xc000001a 0x00000057 0x00570001 nt_status_unable_to_free_vm“的参数是不正确的。”
0 0xc000001b 0x00000057 0x00570001 nt_status_unable_to_delete_section“的参数是不正确的。” 0 0xc000001c 0x00000001 0x00010001 nt_status_invalid_system_service“不正确的函数。”
0 0xc000001d 0xc000001d 0x001d0001 nt_status_illegal_instruction“nt_status_illegal_instruction”
0 0xc000001e 0x00000005 0x00050001 nt_status_invalid_lock_sequence“访问被拒绝。”
0 0xc000001f 0x00000005 0x00050001 nt_status_invalid_view_size“访问被拒绝。”
0 0xc0000020 0x000000c1 0x00c10001 nt_status_invalid_file_for_section“不是有效的windows nt应用程序。” 0 0xc0000021 0x00000005 0x00050001 nt_status_already_committed“访问被拒绝。” 0xc0000022 0x00000005 0x00050001 nt_status_access_denied“访问被拒绝。”
0 0xc0000023 0x0000007a 0x007a0001 nt_status_buffer_too_small“数据区域传递给系统调用是太小了。”
0 0xc0000024 0x00000006 0x00060001 nt_status_object_type_mismatch“句柄无效。”
0 0xc0000025 0xc0000025 0x00250001 nt_status_noncontinuable_exception“nt_status_noncontinuable_exception”
0 0xc0000026 0xc0000026 0x00260001 nt_status_invalid_disposition“nt_status_invalid_disposition” 0 0xc0000027 0x0000013d 0x001f0003 nt_status_unwind“nt_status_unwind” 0 0xc0000028 0x0000013d 0x001f0003 nt_status_bad_stack“nt_status_bad_stack” 0 0xc0000029 0x0000013d 0x001f0003 nt_status_invalid_unwind_target“nt_status_invalid_unwind_target” 0 0xc000002a 0x0000009e 0x009e0001 nt_status_not_locked“段已解除锁定。”
0 0xc000002b 0xc000002b 0x002b0001 nt_status_parity_error“nt_status_parity_error” 0 0xc000002c 0x000001e7 0x01e70001 nt_status_unable_to_decommit_vm“试图访问无效的地址。”
0 0xc000002d 0x000001e7 0x01e70001 nt_status_not_committed“试图访问无效的地址。”
0 0xc000002e 0x0000013d 0x001f0003 nt_status_invalid_port_attributes“nt_status_invalid_port_attributes”
0 0xc000002f 0x0000013d 0x001f0003 nt_status_port_message_too_long“nt_status_port_message_too_long” 0 0xc0000030 0x00000057 0x00570001 nt_status_invalid_parameter_mix“的参数是不正确的。”
0 0xc0000031 0x0000013d 0x001f0003 nt_status_invalid_quota_lower“nt_status_invalid_quota_lower”
0 0xc0000032 0x00000571 0x05710001 nt_status_disk_corrupt_error“磁盘结构已损坏，无法读取。” 0xc0000033 0x0000007b 0x007b0001 nt_status_object_name_invalid“的文件名，目录名或卷标语法不正确。” 0xc0000034 0x00000002 0x00020001 nt_status_object_name_not_found“系统找不到指定的文件。” 0xc0000035 0x000000b7 0x00b70001 nt_status_object_name_collision“无法创建文件时，该文件已经存在。” 0 0xc0000036 0x0000013d 0x001f0003 nt_status_handle_not_waitable“nt_status_handle_not_waitable” 0xc0000037 0x00000006 0x00060001 nt_status_port_disconnected“句柄无效。”
0 0xc0000038 0x0000013d 0x001f0003 nt_status_device_already_attached“nt_status_device_already_attached”
0 0xc0000039 0x000000a1 0x00a10001 nt_status_object_path_invalid“指定的路径无效。” 0xc000003a 0x00000003 0x00030001 nt_status_object_path_not_found“系统找不到指定的路径。” 1 0xc000003b 0x000000a1 0x00a10001 nt_status_object_path_syntax_bad“指定的路径无效。”
0 0xc000003c 0x0000045d 0x045d0001 nt_status_data_overrun“请求不能因为i / o设备错误。”
0 0xc000003d 0x0000045d 0x045d0001 nt_status_data_late_error“请求不能因为i / o设备错误。”
0 0xc000003e 0x00000017 0x00170001 nt_status_data_error“数据错误（循环冗余检查）”
0 0xc000003f 0x00000017 0x00170001 nt_status_crc_error“数据错误（循环冗余检查）”
0 0xc0000040 0x00000008 0x00080001 nt_status_section_too_big“没有足够的存储是可用来处理此命令。” 0 0xc0000041 0x00000005 0x00050001 nt_status_port_connection_refused“访问被拒绝。”
0 0xc0000042 0x00000006 0x00060001 nt_status_invalid_port_handle“句柄无效。” 0xc0000043 0x00000020 0x00200001 nt_status_sharing_violation“该进程无法访问文件，因为它正由另一个进程使用。”
0 0xc0000044 0x00000718 0x07180001 nt_status_quota_exceeded“没有足够的配额是可用来处理此命令。”
0 0xc0000045 0x00000057 0x00570001 nt_status_invalid_page_protection“的参数是不正确的。”
0 0xc0000046 0x00000120 0x01200001 nt_status_mutant_not_owned“企图释放并非呼叫方所拥有的互斥体。” 0 0xc0000047 0x0000012a 0x012a0001 nt_status_semaphore_limit_exceeded“有太多的职位作了一个信号。” 0 0xc0000048 0x00000057 0x00570001 nt_status_port_already_set“的参数是不正确的。”
0 0xc0000049 0x00000057 0x00570001 nt_status_section_not_image“的参数是不正确的。” 0 0xc000004a 0x0000009c 0x009c0001 nt_status_suspend_count_exceeded“接收进程已拒绝此信号。”
0 0xc000004b 0x00000005 0x00050001 nt_status_thread_is_terminating“访问被拒绝。”
0 0xc000004c 0x00000057 0x00570001 nt_status_bad_working_set_limit“的参数是不正确的。”
0 0xc000004d 0x00000057 0x00570001 nt_status_incompatible_file_map“的参数是不正确的。”
0 0xc000004e 0x00000057 0x00570001 nt_status_section_protection“的参数是不正确的。”
0 0xc000004f 0x0000013d 0x001f0003 nt_status_eas_not_supported“nt_status_eas_not_supported”
0 0xc0000050 0x000000ff 0x00ff0001 nt_status_ea_too_large“扩展属性不一致。”
0 0xc0000051 0x00000570 0x05700001 nt_status_nonexistent_ea_entry“文件或目录已损坏，无法读取。”
0 0xc0000052 0x00000570 0x05700001 nt_status_no_eas_on_file“文件或目录已损坏，无法读取。”
0 0xc0000053 0x00000570 nt_status_ea_corrupt_error 0x05700001“文件或目录已损坏，无法读取。”
0 0xc0000054 0x00000021 0x00210001 nt_status_file_lock_conflict“该进程无法访问文件，因为另一个程序已锁定文件的一部分。”
0 0xc0000055 0x00000021 0x00210001 nt_status_lock_not_granted“该进程无法访问文件，因为另一个程序已锁定文件的一部分。” 0xc0000056 0x00000005 0x00050001 nt_status_delete_pending“访问被拒绝。” 0 0xc0000057 0x00000032 0x00320001 nt_status_ctl_file_not_supported“网络请求不支持。”
0 0xc0000058 0x00000519 0x05190001 nt_status_unknown_revision“修订级别是未知的。”
0 0xc0000059 0x0000051a 0x051a0001 nt_status_revision_mismatch“表明两个修订级别是不兼容。”
0 0xc000005a 0x0000051b 0x051b0001 nt_status_invalid_owner“这个安全id不能指派为这个对象的所有者。”
0 0xc000005b 0x0000051c 0x051c0001 nt_status_invalid_primary_group“这个安全id不能指派为对象的主要组。” 0 0xc000005c 0x0000051d 0x051d0001 nt_status_no_impersonation_token“的尝试已取得经营上的一个线程模拟目前未模仿客户端的标记。” 0 0xc000005d 0x0000051e 0x051e0001 nt_status_cant_disable_mandatory“小组可能不会被禁用。”
0 0xc000005e 0x0000051f 0x051f0001 nt_status_no_logon_servers“目前没有可用的登录服务器来服务登录请求。”
0 0xc000005f 0x00000520 0x05200001 nt_status_no_such_logon_session“指定的登录会话不存在。它可能已经被终止。”
0 0xc0000060 0x00000521 0x05210001 nt_status_no_such_privilege“指定的特权不存在。”
0 0xc0000061 0x00000522 0x05220001 nt_status_privilege_not_held“一个所需的特权不持有的客户。”
0 0xc0000062 0x00000523 0x05230001 nt_status_invalid_account_name“提供的名称不是正确格式的帐户名。”
0 0xc0000063 0x00000524 0x05240001 nt_status_user_exists“指定用户已经存在。” 0xc0000064 0x00000525 0x05250001 nt_status_no_such_user“指定的用户不存在。”
0 0xc0000065 0x00000526 0x05260001 nt_status_group_exists“指定的群组已经存在。”
0 0xc0000066 0x00000527 0x05270001 nt_status_no_such_group“指定的组不存在。”
0 0xc0000067 0x00000528 0x05280001 nt_status_member_in_group“不是指定的用户帐户已是指定组的成员，或指定的组不能被删除，因为它包含了一个成员。”
0 0xc0000068 0x00000529 0x05290001 nt_status_member_not_in_group“指定的用户帐户不是指定组帐户的成员。”
0 0xc0000069 0x0000052a nt_status_last_admin 0x052a0001“最后剩下的管理帐户无法禁用或删除。” 0xc000006a 0x00000056 0x00560001 nt_status_wrong_password“指定的网络密码不正确。”
0 0xc000006b 0x0000052c 0x052c0001 nt_status_ill_formed_password“无法更新密码。为新密码提供的值包含密码中不属于允许的值。” 0 0xc000006c 0x0000052d 0x052d0001 nt_status_password_restriction“无法更新密码，因为密码更新规则已被侵犯。” 1 0xc000006d 0x0000052e 0x052e0001 nt_status_logon_failure“登录失败：。未知的用户名或错误密码” 0xc000006e 0x0000052f 0x052f0001 nt_status_account_restriction“登录失败：用户帐户限制。” 0xc000006f 0x00000530 0x05300001 nt_status_invalid_logon_hours“登录失败：。帐户登录时间限制违反” 0xc0000070 0x00000531 0x05310001 nt_status_invalid_workstation“登录失败：不允许用户登录到这台计算机。” 0xc0000071 0x00000532 0x05320001 nt_status_password_expired“登录失败：指定的帐户密码已过期。” 0xc0000072 0x00000533 0x05330001 nt_status_account_disabled“登录失败：帐户目前已停用。”
0 0xc0000073 0x00000534 0x05340001 nt_status_none_mapped“没有进行帐户名和安全id映射完成。”
0 0xc0000074 0x00000535 nt_status_too_many_luids_requested 0x05350001“太多的本地用户标识符（luids）被要求在同一时间。”
0 0xc0000075 0x00000536 0x05360001 nt_status_luids_exhausted“没有更多的本地用户标识符（luids）可供选择。”
0 0xc0000076 0x00000537 0x05370001 nt_status_invalid_sub_authority“一个安全id subauthority部分是这一特定使用无效。”
0 0xc0000077 0x00000538 0x05380001 nt_status_invalid_acl“访问控制列表（acl）的结构是无效的。”
0 0xc0000078 0x00000539 0x05390001 nt_status_invalid_sid“安全id结构是无效的。” 0 0xc0000079 0x0000053a 0x053a0001 nt_status_invalid_security_descr“安全描述符结构无效。”
0 0xc000007a 0x0000007f 0x007f0001 nt_status_procedure_not_found“指定的程序不能被发现。”
0 0xc000007b 0x000000c1 0x00c10001 nt_status_invalid_image_format“％1不是有效的windows nt应用程序。”
0 0xc000007c 0x000003f0 0x03f00001 nt_status_no_token“一个试图引用一个不存在的令牌。”
0 0xc000007d 0x0000053c 0x053c0001 nt_status_bad_inheritance_acl“继承的访问控制列表（acl）或访问控制项（ace）无法建立。”
0 0xc000007e 0x0000009e 0x009e0001 nt_status_range_not_locked“段已解除锁定。”
0 0xc000007f 0x00000070 0x00700001 nt_status_disk_full“没有足够的磁盘空间。”
0 0xc0000080 0x0000053d 0x053d0001 nt_status_server_disabled“服务器目前已停用。”
0 0xc0000081 0x0000053e 0x053e0001 nt_status_server_not_disabled“的服务器目前已启用。” 0 0xc0000082 0x00000044 0x00440001 nt_status_too_many_guids_requested他说：“本地计算机网络适配器卡的名称限制超过。”
0 0xc0000083 0x00000103 0x01030001 nt_status_guids_exhausted“没有更多的资料。”
0 0xc0000084 0x0000053f 0x053f0001 nt_status_invalid_id_authority“提供的值是一个无效值的标识符的权威。”
0 0xc0000085 0x00000103 0x01030001 nt_status_agents_exhausted“没有更多的资料。”
0 0xc0000086 0x0000009a 0x009a0001 nt_status_invalid_volume_label“您输入的卷标超过目标文件系统标签字符的限制。”
0 0xc0000087 0x0000000e 0x000e0001 nt_status_section_not_extended“没有足够的存储可用于完成此操作”。
0 0xc0000088 0x000001e7 0x01e70001 nt_status_not_mapped_data“试图访问无效的地址。”
0 0xc0000089 0x00000714 0x07140001 nt_status_resource_data_not_found“指定的图像文件不包含资源部分。” 0 0xc000008a 0x00000715 0x07150001 nt_status_resource_type_not_found“指定的资源类型中无法找到该图像文件。”
0 0xc000008b 0x00000716 0x07160001 nt_status_resource_name_not_found“指定的资源名称不能找到该图像文件。”
0 0xc000008c 0xc000008c 0x008c0001 nt_status_array_bounds_exceeded“nt_status_array_bounds_exceeded” 0 0xc000008d 0xc000008d 0x008d0001 nt_status_float_denormal_operand“nt_status_float_denormal_operand” 0 0xc000008e 0xc000008e 0x008e0001 nt_status_float_spanide_by_zero“nt_status_float_spanide_by_zero” 0 0xc000008f 0xc000008f 0x008f0001 nt_status_float_inexact_result“nt_status_float_inexact_result” 0 0xc0000090 0xc0000090 0x00900001 nt_status_float_invalid_operation“nt_status_float_invalid_operation”
0 0xc0000091 0xc0000091 0x00910001 nt_status_float_overflow“nt_status_float_overflow” 0 0xc0000092 0xc0000092 0x00920001 nt_status_float_stack_check“nt_status_float_stack_check” 0 0xc0000093 0xc0000093 0x00930001 nt_status_float_underflow“nt_status_float_underflow” 0 0xc0000094 0xc0000094 0x00940001 nt_status_integer_spanide_by_zero“nt_status_integer_spanide_by_zero” 0 0xc0000095 0x00000216 0x02160001 nt_status_integer_overflow“算术结果超过32位。” 0 0xc0000096 0xc0000096 0x00960001 nt_status_privileged_instruction“nt_status_privileged_instruction” 0 0xc0000097 0x00000008 0x00080001 nt_status_too_many_paging_files“没有足够的存储是可用来处理此命令。”
0 0xc0000098 0x000003ee 0x03ee0001 nt_status_file_invalid“对文件的卷已被外部改变，这样打开的文件不再有效。” 0 0xc0000099 0x00000540 0x05400001 nt_status_allotted_space_exceeded“没有更多的内存可用于更新安全信息。” 0 0xc000009a 0x000005aa 0x05aa0001 nt_status_insufficient_resources“系统资源不足，无法完成请求的服务。”
0 0xc000009b 0x00000003 0x00030001 nt_status_dfs_exit_path_found“系统找不到指定的路径。”
0 0xc000009c 0x00000017 0x00170001 nt_status_device_data_error“数据错误（循环冗余检查）”
0 0xc000009d 0x00000015 0x00150001 nt_status_device_not_connected“的设备没有准备好。”
0 0xc000009e 0x00000015 0x00150001 nt_status_device_power_failure“的设备没有准备好。”
0 0xc000009f 0x000001e7 0x01e70001 nt_status_free_vm_not_at_base“试图访问无效的地址。”
0 0xc00000a0 0x000001e7 0x01e70001 nt_status_memory_not_allocated“试图访问无效的地址。”
0 0xc00000a1 0x000005ad 0x05ad0001 nt_status_working_set_quota“配额不足，无法完成请求的服务。”
0 0xc00000a2 0x00000013 0x00130001 nt_status_media_write_protected“媒体是写保护。”
0 0xc00000a3 0x00000015 0x00150001 nt_status_device_not_ready“的设备没有准备好。”
0 0xc00000a4 0x00000541 0x05410001 nt_status_invalid_group_attributes“指定属性无效，或与整个群体的属性不兼容。”
0 0xc00000a5 0x00000542 0x05420001 nt_status_bad_impersonation_level“必须提供所需的模拟级别没有提供，或提供的模拟级别无效。”
0 0xc00000a6 0x00000543 0x05430001 nt_status_cant_open_anonymous“无法打开一匿名级别的安全性令牌。”
0 0xc00000a7 0x00000544 0x05440001 nt_status_bad_validation_class“要求的验证信息类是无效的。”
0 0xc00000a8 0x00000545 0x05450001 nt_status_bad_token_type“令牌的类型对其尝试使用不恰当的。”
0 0xc00000a9 0x0000013d 0x001f0003 nt_status_bad_master_boot_record“nt_status_bad_master_boot_record” 0 0xc00000aa 0x0000013d 0x001f0003 nt_status_instruction_misalignment“nt_status_instruction_misalignment” 1 0xc00000ab 0x000000e7 0x00e70001 nt_status_instance_not_available“所有的管道实例都很忙。” 0xc00000ac 0x000000e7 0x00e70001 nt_status_pipe_not_available“所有的管道实例都很忙。” 0xc00000ad 0x000000e6 0x00e60001 nt_status_invalid_pipe_state“管道状态无效。” 0xc00000ae 0x000000e7 0x00e70001 nt_status_pipe_busy“所有的管道实例都很忙。”
0 0xc00000af 0x00000001 0x00010001 nt_status_illegal_function“不正确的函数。” 0xc00000b0 0x000000e9 0x00e90001 nt_status_pipe_disconnected“没有进程在管道的另一端。” 0xc00000b1 0x000000e8 0x00e80001 nt_status_pipe_closing“管道正在关闭。”
0 0xc00000b2 0x00000217 0x02170001 nt_status_pipe_connected“上有一个管道的另一端的过程。” 0xc00000b3 0x00000218 0x02180001 nt_status_pipe_listening“正在等待一个进程打开管道的另一端。”
0 0xc00000b4 0x000000e6 0x00e60001 nt_status_invalid_read_mode“管道状态无效。”
0 0xc00000b5 0x00000079 nt_status_io_timeout 0x00790001“信号灯超时时间已过期。”
0 0xc00000b6 0x00000026 0x00260001 nt_status_file_forced_closed“的文件达成的结束。”
0 0xc00000b7 0x0000013d 0x001f0003 nt_status_profiling_not_started“nt_status_profiling_not_started” 0 0xc00000b8 0x0000013d 0x001f0003 nt_status_profiling_not_stopped“nt_status_profiling_not_stopped” 0 0xc00000b9 0x0000013d 0x001f0003 nt_status_could_not_interpret“nt_status_could_not_interpret” 0xc00000ba 0x00000005 0x00050001 nt_status_file_is_a_directory“访问被拒绝。”
0 0xc00000bb 0x00000032 0x00320001 nt_status_not_supported“网络请求不支持。”
0 0xc00000bc 0x00000033 0x00330001 nt_status_remote_not_listening“远程计算机不可用。”
0 0xc00000bd 0x00000034 0x00340001 nt_status_duplicate_name“重复的名称在网络上存在。”
0 0xc00000be 0x00000035 0x00350001 nt_status_bad_network_path“网络路径没有被发现。” 0 0xc00000bf 0x00000036 0x00360001 nt_status_network_busy“网络正忙。” 0 0xc00000c0 0x00000037 0x00370001 nt_status_device_does_not_exist“指定网络资源或设备不再可用。”
0 0xc00000c1 0x00000038 0x00380001 nt_status_too_many_commands“网络bios命令限制已经达到。” 0 0xc00000c2 0x00000039 0x00390001 nt_status_adapter_hardware_error“网络适配器硬件错误。”
0 0xc00000c3 0x0000003a 0x003a0001 nt_status_invalid_network_response“指定的伺服器无法执行要求的作业。” 0 0xc00000c4 0x0000003b 0x003b0001 nt_status_unexpected_network_error“一个意外的网络错误。”
0 0xc00000c5 0x0000003c 0x003c0001 nt_status_bad_remote_adapter“的远程适配器不兼容。”
0 0xc00000c6 0x0000003d 0x003d0001 nt_status_print_queue_full“打印机队列已满。”
0 0xc00000c7 0x0000003e 0x003e0001 nt_status_no_spool_space“空间来存储等待打印的文件是不是在服务器上可用。”
0 0xc00000c8 0x0000003f 0x003f0001 nt_status_print_cancelled“你的等待打印文件已被删除。”
0 0xc00000c9 0x00000040 0x00400001 nt_status_network_name_deleted“指定的网络名不再可用。”
0 0xc00000ca 0x00000041 0x00410001 nt_status_network_access_denied“网络访问被拒绝。”
0 0xc00000cb 0x00000042 0x00420001 nt_status_bad_device_type“网络资源类型不正确的。” 0xc00000cc 0x00000043 0x00430001 nt_status_bad_network_name“网络名称不能找到。”
0 0xc00000cd 0x00000044 0x00440001 nt_status_too_many_names他说：“本地计算机网络适配器卡的名称限制超过。”
0 0xc00000ce 0x00000045 0x00450001 nt_status_too_many_sessions“网络bios会话限制被超过。”
0 0xc00000cf 0x00000046 0x00460001 nt_status_sharing_paused“远程服务器已暂停或正在启动过程中。”
0 0xc00000d0 0x00000047 0x00470001 nt_status_request_not_accepted“没有更多的连接，可在这个时候到这台远程计算机，因为只要有计算机可以接受多个连接了。”
0 0xc00000d1 0x00000048 0x00480001 nt_status_redirector_paused“指定的打印机或磁盘装置已经暂停。”
0 0xc00000d2 0x00000058 0x00580001 nt_status_net_write_fault“写在网络上出现故障。”
0 0xc00000d3 0x0000013d 0x001f0003 nt_status_profiling_at_limit“nt_status_profiling_at_limit”
0 0xc00000d4 0x00000011 0x00110001 nt_status_not_same_device“系统无法将文件移动到一个不同的磁盘驱动器。” 0 0xc00000d5 0x0000013d 0x001f0003 nt_status_file_renamed“nt_status_file_renamed” 0 0xc00000d6 0x000000f0 0x00f00001 nt_status_virtual_circuit_closed“会议被取消。”
0 0xc00000d7 0x00000546 0x05460001 nt_status_no_security_on_object“无法执行的对象又没有相关的安全性的安全运作。” 0 0xc00000d8 0x0000013d 0x001f0003 nt_status_cant_wait“nt_status_cant_wait”
0 0xc00000d9 0x000000e8 0x00e80001 nt_status_pipe_empty“管道正在关闭。”
0 0xc00000da 0x00000547 0x05470001 nt_status_cant_access_domain_info“表示windows nt服务器无法联系，或在域对象的保护等必要的信息无法收回。” 0 0xc00000db 0x0000013d 0x001f0003 nt_status_cant_terminate_self“nt_status_cant_terminate_self”
0 0xc00000dc 0x00000548 0x05480001 nt_status_invalid_server_state“安全帐户管理器（sam）或本地安全颁发机构（lsa）服务器处于错误状态来执行安全操作。”
0 0xc00000dd 0x00000549 0x05490001 nt_status_invalid_domain_state“领域中的错误状态来执行安全操作了。”
0 0xc00000de 0x0000054a 0x054a0001 nt_status_invalid_domain_role“这个操作只允许在主域控制器的域。”
0 0xc00000df 0x0000054b nt_status_no_such_domain 0x054b0001“指定的域不存在。”
0 0xc00000e0 0x0000054c 0x054c0001 nt_status_domain_exists“指定的域已存在。”
0 0xc00000e1 0x0000054d 0x054d0001 nt_status_domain_limit_exceeded“一个试图超过每个服务器上的域的数量限制。” 0 0xc00000e2 0x0000013d 0x001f0003 nt_status_oplock_not_granted“nt_status_oplock_not_granted” 0 0xc00000e3 0x0000013d 0x001f0003 nt_status_invalid_oplock_protocol“nt_status_invalid_oplock_protocol” 0 0xc00000e4 0x0000054e 0x054e0001 nt_status_internal_db_corruption“无法完成，因为无论是灾难性的介质故障或磁盘上的数据结构损坏的请求的操作。”
0 0xc00000e5 0x0000054f 0x054f0001 nt_status_internal_error“安全帐户数据库包含内部不一致的情况。”
0 0xc00000e6 0x00000550 0x05500001 nt_status_generic_not_mapped“通用访问类型的访问掩码中，应该已经被映射到非泛型类型中。”
0 0xc00000e7 0x00000551 0x05510001 nt_status_bad_descriptor_format“一个安全描述符是正确的格式（绝对或自相关）不。”
0 0xc00000e8 0x000006f8 0x06f80001 nt_status_invalid_user_buffer“提供的用户缓冲区不为所请求的操作有效。” 0 0xc00000e9 0x0000013d 0x001f0003 nt_status_unexpected_io_error“nt_status_unexpected_io_error” 0 0xc00000ea 0x0000013d 0x001f0003 nt_status_unexpected_mm_create_err“nt_status_unexpected_mm_create_err”
0 0xc00000eb 0x0000013d 0x001f0003 nt_status_unexpected_mm_map_error“nt_status_unexpected_mm_map_error”
0 0xc00000ec 0x0000013d 0x001f0003 nt_status_unexpected_mm_extend_err“nt_status_unexpected_mm_extend_err”
0 0xc00000ed 0x00000552 0x05520001 nt_status_not_logon_process“所要求的行动是由登录使用限制只处理。调用进程未注册为一个登录进程。”
0 0xc00000ee 0x00000553 0x05530001 nt_status_logon_session_exists“无法启动的id已在使用一个新的登录会话。”
0 0xc00000ef 0x00000057 0x00570001 nt_status_invalid_parameter_1“的参数是不正确的。”
0 0xc00000f0 0x00000057 0x00570001 nt_status_invalid_parameter_2“的参数是不正确的。”
0 0xc00000f1 0x00000057 0x00570001 nt_status_invalid_parameter_3“的参数是不正确的。”
0 0xc00000f2 0x00000057 0x00570001 nt_status_invalid_parameter_4“的参数是不正确的。”
0 0xc00000f3 0x00000057 0x00570001 nt_status_invalid_parameter_5“的参数是不正确的。”
0 0xc00000f4 0x00000057 0x00570001 nt_status_invalid_parameter_6“的参数是不正确的。”
0 0xc00000f5 0x00000057 0x00570001 nt_status_invalid_parameter_7“的参数是不正确的。”
0 0xc00000f6 0x00000057 0x00570001 nt_status_invalid_parameter_8“的参数是不正确的。”
0 0xc00000f7 0x00000057 0x00570001 nt_status_invalid_parameter_9“的参数是不正确的。”
0 0xc00000f8 0x00000057 0x00570001 nt_status_invalid_parameter_10“的参数是不正确的。”
0 0xc00000f9 0x00000057 0x00570001 nt_status_invalid_parameter_11“的参数是不正确的。”
0 0xc00000fa 0x00000057 0x00570001 nt_status_invalid_parameter_12“的参数是不正确的。” 0 0xc00000fb 0x00000003 0x00030001 nt_status_redirector_not_started“系统找不到指定的路径。”
0 0xc00000fc 0x0000013d 0x001f0003 nt_status_redirector_started“nt_status_redirector_started” 0 0xc00000fd 0x000003e9 0x03e90001 nt_status_stack_overflow“递归太深，堆栈溢出。”
0 0xc00000fe 0x00000554 0x05540001 nt_status_no_such_package“指定的身份验证数据包是未知的。”
0 0xc00000ff 0x0000013d 0x001f0003 nt_status_bad_function_table“nt_status_bad_function_table”
0 0xc0000101 0x00000091 0x00910001 nt_status_directory_not_empty“目录不是空的。”
0 0xc0000102 0x00000570 nt_status_file_corrupt_error 0x05700001“文件或目录已损坏，无法读取。” 0xc0000103 0x0000010b 0x010b0001 nt_status_not_a_directory“目录名称是无效的。”
0 0xc0000104 0x00000555 0x05550001 nt_status_bad_logon_session_state“中的登录会话的状态与请求的操作不相一致。”
0 0xc0000105 0x00000556 0x05560001 nt_status_logon_session_collision“登录会话标识已在使用。”
0 0xc0000106 0x000000ce 0x00ce0001 nt_status_name_too_long“文件名或扩展名太长。”
0 0xc0000107 0x0000013d 0x001f0003 nt_status_files_open“nt_status_files_open”
0 0xc0000108 0x00000964 0x09640001 nt_status_connection_in_use“设备正被访问的活动进程。”
0 0xc0000109 0x0000013d 0x001f0003 nt_status_message_not_found“nt_status_message_not_found” 0 0xc000010a 0x00000005 0x00050001 nt_status_process_is_terminating“访问被拒绝。”
0 0xc000010b 0x00000557 0x05570001 nt_status_invalid_logon_type“登录请求包含无效的登录类型值。”
0 0xc000010c 0x0000013d 0x001f0003 nt_status_no_guid_translation“nt_status_no_guid_translation”
0 0xc000010d 0x00000558 0x05580001 nt_status_cannot_impersonate“无法模拟通过命名管道，直到数据已经从该管道读取。”
0 0xc000010e 0x00000420 0x04200001 nt_status_image_already_loaded“服务的一个实例已在运行。”
0 0xc000010f 0x0000013d 0x001f0003 nt_status_abios_not_present“nt_status_abios_not_present” 0 0xc0000110 0x0000013d 0x001f0003 nt_status_abios_lid_not_exist“nt_status_abios_lid_not_exist” 0 0xc0000111 0x0000013d 0x001f0003 nt_status_abios_lid_already_owned“nt_status_abios_lid_already_owned”
0 0xc0000112 0x0000013d 0x001f0003 nt_status_abios_not_lid_owner“nt_status_abios_not_lid_owner” 0 0xc0000113 0x0000013d 0x001f0003 nt_status_abios_invalid_command“nt_status_abios_invalid_command” 0 0xc0000114 0x0000013d 0x001f0003 nt_status_abios_invalid_lid“nt_status_abios_invalid_lid” 0 0xc0000115 0x0000013d 0x001f0003 nt_status_abios_selector_not_available“nt_status_abios_selector_not_available”
0 0xc0000116 0x0000013d 0x001f0003 nt_status_abios_invalid_selector“nt_status_abios_invalid_selector” 0 0xc0000117 0x0000013d 0x001f0003 nt_status_no_ldt“nt_status_no_ldt” 0 0xc0000118 0x0000013d 0x001f0003 nt_status_invalid_ldt_size“nt_status_invalid_ldt_size” 0 0xc0000119 0x0000013d 0x001f0003 nt_status_invalid_ldt_offset “nt_status_invalid_ldt_offset” 0 0xc000011a 0x0000013d 0x001f0003 nt_status_invalid_ldt_descriptor “nt_status_invalid_ldt_descriptor” 0 0xc000011b 0x000000c1 0x00c10001 nt_status_invalid_image_ne_format “%1 is not a valid windows nt application.” 0 0xc000011c 0x00000559 0x05590001 nt_status_rxact_invalid_state “the transaction state of a registry subtree is incompatible with the requested operation.” 0 0xc000011d 0x0000055a 0x055a0001 nt_status_rxact_commit_failure “an internal security database corruption has been encountered.” 0 0xc000011e 0x000003ee 0x03ee0001 nt_status_mapped_file_size_zero “the volume for a file has been externally altered such that the opened file is no longer valid.” 0 0xc000011f 0x00000004 0x00040001 nt_status_too_many_opened_files “the system cannot open the file.” 0 0xc0000120 0x000003e3 0x03e30001 nt_status_cancelled “the i/o operation has been aborted because of either a thread exit or an application request.” 1 0xc0000121 0x00000005 0x00050001 nt_status_cannot_delete “access is denied.” 0 0xc0000122 0x000004ba 0x04ba0001 nt_status_invalid_computer_name “the format of the specified computer name is invalid.” 0 0xc0000123 0x00000005 0x00050001 nt_status_file_deleted “access is denied.” 0 0xc0000124 0x0000055b 0x055b0001 nt_status_special_account “cannot perform this operation on built-in accounts.” 0 0xc0000125 0x0000055c 0x055c0001 nt_status_special_group “cannot perform this operation on this built-in special group.” 0 0xc0000126 0x0000055d 0x055d0001 nt_status_special_user “cannot perform this operation on this built-in special user.” 0 0xc0000127 0x0000055e 0x055e0001 nt_status_members_primary_group “the user cannot be removed from a group because the group is currently the user's primary group.” 0 0xc0000128 0x00000006 0x00060001 nt_status_file_closed “the handle is invalid.” 0 0xc0000129 0x0000013d 0x001f0003 nt_status_too_many_threads “nt_status_too_many_threads” 0 0xc000012a 0x0000013d 0x001f0003 nt_status_thread_not_in_process “nt_status_thread_not_in_process” 0 0xc000012b 0x0000055f 0x055f0001 nt_status_token_already_in_use “the token is already in use as a primary token.” 0 0xc000012c 0x0000013d 0x001f0003 nt_status_pagefile_quota_exceeded “nt_status_pagefile_quota_exceeded” 0 0xc000012d 0x000005af 0x05af0001 nt_status_commitment_limit “the paging file is too small for this operation to complete.” 0 0xc000012e 0x000000c1 0x00c10001 nt_status_invalid_image_le_format “%1 is not a valid windows nt application.” 0 0xc000012f 0x000000c1 0x00c10001 nt_status_invalid_image_not_mz “%1 is not a valid windows nt application.” 0 0xc0000130 0x000000c1 0x00c10001 nt_status_invalid_image_protect “%1 is not a valid windows nt application.” 0 0xc0000131 0x000000c1 0x00c10001 nt_status_invalid_image_win_16 “%1 is not a valid windows nt application.” 0 0xc0000132 0x0000013d 0x001f0003 nt_status_logon_server_conflict “nt_status_logon_server_conflict” 0 0xc0000133 0x0000013d 0x001f0003 nt_status_time_difference_at_dc “nt_status_time_difference_at_dc” 0 0xc0000134 0x0000013d 0x001f0003 nt_status_synchronization_required “nt_status_synchronization_required” 0 0xc0000135 0x0000007e 0x007e0001 nt_status_dll_not_found “the specified module could not be found.” 0 0xc0000136 0x0000013d 0x001f0003 nt_status_open_failed “nt_status_open_failed” 0 0xc0000137 0x0000013d 0x001f0003 nt_status_io_privilege_failed “nt_status_io_privilege_failed” 0 0xc0000138 0x000000b6 0x00b60001 nt_status_ordinal_not_found “the operating system cannot run %1.” 0 0xc0000139 0x0000007f 0x007f0001 nt_status_entrypoint_not_found “the specified procedure could not be found.” 0 0xc000013a 0x0000013d 0x001f0003 nt_status_control_c_exit “nt_status_control_c_exit” 0 0xc000013b 0x00000040 0x00400001 nt_status_local_disconnect “the specified network name is no longer available.” 0 0xc000013c 0x00000040 0x00400001 nt_status_remote_disconnect “the specified network name is no longer available.” 0 0xc000013d 0x00000033 0x00330001 nt_status_remote_resources “the remote computer is not available.” 0 0xc000013e 0x0000003b 0x003b0001 nt_status_link_failed “an unexpected network error occurred.” 0 0xc000013f 0x0000003b 0x003b0001 nt_status_link_timeout “an unexpected network error occurred.” 0 0xc0000140 0x0000003b 0x003b0001 nt_status_invalid_connection “an unexpected network error occurred.” 0 0xc0000141 0x0000003b 0x003b0001 nt_status_invalid_address “an unexpected network error occurred.” 0 0xc0000142 0x0000045a 0x045a0001 nt_status_dll_init_failed “a dynamic link library(dll)initialization routine failed.” 0 0xc0000143 0x0000013d 0x001f0003 nt_status_missing_systemfile “nt_status_missing_systemfile” 0 0xc0000144 0x0000013d 0x001f0003 nt_status_unhandled_exception “nt_status_unhandled_exception” 0 0xc0000145 0x0000013d 0x001f0003 nt_status_app_init_failure “nt_status_app_init_failure” 0 0xc0000146 0x0000013d 0x001f0003 nt_status_pagefile_create_failed “nt_status_pagefile_create_failed” 0 0xc0000147 0x0000013d 0x001f0003 nt_status_no_pagefile “nt_status_no_pagefile” 0 0xc0000148 0x0000007c 0x007c0001 nt_status_invalid_level “the system call level is not correct.” 0 0xc0000149 0x00000056 0x00560001 nt_status_wrong_password_core “the specified network password is not correct.” 0 0xc000014a 0x0000013d 0x001f0003 nt_status_illegal_float_context “nt_status_illegal_float_context” 1 0xc000014b 0x0000006d 0x006d0001 nt_status_pipe_broken “the pipe has been ended.” 0 0xc000014c 0x000003f1 0x03f10001 nt_status_registry_corrupt “the configuration registry database is corrupt.” 0 0xc000014d 0x000003f8 0x03f80001 nt_status_registry_io_failed “an i/o operation initiated by the registry failed registry could not read in, or write out, or flush, one of the files that contain the system's image of the registry.” 0 0xc000014e 0x0000013d 0x001f0003 nt_status_no_event_pair “nt_status_no_event_pair” 0 0xc000014f 0x000003ed 0x03ed0001 nt_status_unrecognized_volume “the volume does not contain a recognized file make sure that all required file system drivers are loaded and that the volume is not corrupt.” 0 0xc0000150 0x0000045e 0x045e0001 nt_status_serial_no_device_inited “no serial device was successfully serial driver will unload.” 0 0xc0000151 0x00000560 0x05600001 nt_status_no_such_alias “the specified local group does not exist.” 0 0xc0000152 0x00000561 0x05610001 nt_status_member_not_in_alias “the specified account name is not a member of the local group.” 0 0xc0000153 0x00000562 0x05620001 nt_status_member_in_alias “the specified account name is already a member of the local group.” 0 0xc0000154 0x00000563 0x05630001 nt_status_alias_exists “the specified local group already exists.” 0 0xc0000155 0x00000564 0x05640001 nt_status_logon_not_granted “logon failure: the user has not been granted the requested logon type at this computer.” 0 0xc0000156 0x00000565 0x05650001 nt_status_too_many_secrets “the maximum number of secrets that may be stored in a single system has been exceeded.” 0 0xc0000157 0x00000566 0x05660001 nt_status_secret_too_long “the length of a secret exceeds the maximum length allowed.” 0 0xc0000158 0x00000567 0x05670001 nt_status_internal_db_error “the local security authority database contains an internal inconsistency.” 0 0xc0000159 0x000003ef 0x03ef0001 nt_status_fullscreen_mode “the requested operation cannot be performed in full-screen mode.” 0 0xc000015a 0x00000568 0x05680001 nt_status_too_many_context_ids “during a logon attempt, the user's security context accumulated too many security ids.” 1 0xc000015b 0x00000569 0x05690001 nt_status_logon_type_not_granted “logon failure: the user has not been granted the requested logon type at this computer.” 0 0xc000015c 0x000003f9 0x03f90001 nt_status_not_registry_file “the system has attempted to load or restore a file into the registry, but the specified file is not in a registry file format.” 0 0xc000015d 0x0000056a 0x056a0001 nt_status_nt_cross_encryption_required “a cross-encrypted password is necessary to change a user password.” 0 0xc000015e 0x0000013d 0x001f0003 nt_status_domain_ctrlr_config_error “nt_status_domain_ctrlr_config_error” 0 0xc000015f 0x0000045d 0x045d0001 nt_status_ft_missing_member “the request could not be performed because of an i/o device error.” 0 0xc0000160 0x0000013d 0x001f0003 nt_status_ill_formed_service_entry “nt_status_ill_formed_service_entry” 0 0xc0000161 0x0000013d 0x001f0003 nt_status_illegal_character “nt_status_illegal_character” 0 0xc0000162 0x00000459 0x04590001 nt_status_unmappable_character “no mapping for the unicode character exists in the target multi-byte code page.” 0 0xc0000163 0x0000013d 0x001f0003 nt_status_undefined_character “nt_status_undefined_character” 0 0xc0000164 0x0000013d 0x001f0003 nt_status_floppy_volume “nt_status_floppy_volume” 0 0xc0000165 0x00000462 0x04620001 nt_status_floppy_id_mark_not_found “no id address mark was found on the floppy disk.” 0 0xc0000166 0x00000463 0x04630001 nt_status_floppy_wrong_cylinder “mismatch between the floppy disk sector id field and the floppy disk controller track address.” 0 0xc0000167 0x00000464 0x04640001 nt_status_floppy_unknown_error “the floppy disk controller reported an error that is not recognized by the floppy disk driver.” 0 0xc0000168 0x00000465 0x04650001 nt_status_floppy_bad_registers “the floppy disk controller returned inconsistent results in its registers.” 0 0xc0000169 0x00000466 0x04660001 nt_status_disk_recalibrate_failed “while accessing the hard disk, a recalibrate operation failed, even after retries.” 0 0xc000016a 0x00000467 0x04670001 nt_status_disk_operation_failed “while accessing the hard disk, a disk operation failed even after retries.” 0 0xc000016b 0x00000468 0x04680001 nt_status_disk_reset_failed “while accessing the hard disk, a disk controller reset was needed, but even that failed.” 0 0xc000016c 0x0000045f 0x045f0001 nt_status_shared_irq_busy “unable to open a device that was sharing an interrupt request(irq)with other least one other device that uses that irq was already opened.” 0 0xc000016d 0x0000045d 0x045d0001 nt_status_ft_orphaning “the request could not be performed because of an i/o device error.” 0 0xc0000172 0x00000451 0x04510001 nt_status_partition_failure “tape could not be partitioned.” 0 0xc0000173 0x00000452 0x04520001 nt_status_invalid_block_length “when accessing a new tape of a multivolume partition, the current blocksize is incorrect.” 0 0xc0000174 0x00000453 0x04530001 nt_status_device_not_partitioned “tape partition information could not be found when loading a tape.” 0 0xc0000175 0x00000454 0x04540001 nt_status_unable_to_lock_media “unable to lock the media eject mechanism.” 0 0xc0000176 0x00000455 0x04550001 nt_status_unable_to_unload_media “unable to unload the media.” 0 0xc0000177 0x00000469 0x04690001 nt_status_eom_overflow “physical end of tape encountered.” 0 0xc0000178 0x00000458 0x04580001 nt_status_no_media “no media in drive.” 0 0xc000017a 0x0000056b 0x056b0001 nt_status_no_such_member “a new member could not be added to a local group because the member does not exist.” 0 0xc000017b 0x0000056c 0x056c0001 nt_status_invalid_member “a new member could not be added to a local group because the member has the wrong account type.” 0 0xc000017c 0x000003fa 0x03fa0001 nt_status_key_deleted “illegal operation attempted on a registry key which has been marked for deletion.” 0 0xc000017d 0x000003fb 0x03fb0001 nt_status_no_log_space “system could not allocate the required space in a registry log.” 0 0xc000017e 0x0000056d 0x056d0001 nt_status_too_many_sids “too many security ids have been specified.” 0 0xc000017f 0x0000056e 0x056e0001 nt_status_lm_cross_encryption_required “a cross-encrypted password is necessary to change this user password.” 0 0xc0000180 0x000003fc 0x03fc0001 nt_status_key_has_children “cannot create a symbolic link in a registry key that already has subkeys or values.” 0 0xc0000181 0x000003fd 0x03fd0001 nt_status_child_must_be_volatile “cannot create a stable subkey under a volatile parent key.” 0 0xc0000182 0x00000057 0x00570001 nt_status_device_configuration_error “the parameter is incorrect.” 0 0xc0000183 0x0000045d 0x045d0001 nt_status_driver_internal_error “the request could not be performed because of an i/o device error.” 0 0xc0000184 0x00000016 0x00160001 nt_status_invalid_device_state “the device does not recognize the command.” 0 0xc0000185 0x0000045d 0x045d0001 nt_status_io_device_error “the request could not be performed because of an i/o device error.” 0 0xc0000186 0x0000045d 0x045d0001 nt_status_device_protocol_error “the request could not be performed because of an i/o device error.” 0 0xc0000187 0x0000013d 0x001f0003 nt_status_backup_controller “nt_status_backup_controller” 0 0xc0000188 0x000005de 0x05de0001 nt_status_log_file_full “the event log file is full.” 0 0xc0000189 0x00000013 0x00130001 nt_status_too_late “the media is write protected.” 0 0xc000018a 0x000006fa 0x06fa0001 nt_status_no_trust_lsa_secret “the workstation does not have a trust secret.” 0 0xc000018b 0x000006fb 0x06fb0001 nt_status_no_trust_sam_account “the sam database on the windows nt server does not have a computer account for this workstation trust relationship.” 0 0xc000018c 0x000006fc 0x06fc0001 nt_status_trusted_domain_failure “the trust relationship between the primary domain and the trusted domain failed.” 0 0xc000018d 0x000006fd 0x06fd0001 nt_status_trusted_relationship_failure “the trust relationship between this workstation and the primary domain failed.” 0 0xc000018e 0x000005dc 0x05dc0001 nt_status_eventlog_file_corrupt “the event log file is corrupt.” 0 0xc000018f 0x000005dd 0x05dd0001 nt_status_eventlog_cant_start “no event log file could be opened, so the event logging service did not start.” 0 0xc0000190 0x000006fe 0x06fe0001 nt_status_trust_failure “the network logon failed.” 0 0xc0000191 0x0000013d 0x001f0003 nt_status_mutant_limit_exceeded “nt_status_mutant_limit_exceeded” 0 0xc0000192 0x00000700 0x07000001 nt_status_netlogon_not_started “an attempt was made to logon, but the network logon service was not started.” 0 0xc0000193 0x00000701 0x07010001 nt_status_account_expired “the user's account has expired.” 0 0xc0000194 0x0000046b 0x046b0001 nt_status_possible_deadlock “a potential deadlock condition has been detected.” 0 0xc0000195 0x000004c3 0x04c30001 nt_status_network_credential_conflict “the credentials supplied conflict with an existing set of credentials.” 0 0xc0000196 0x000004c4 0x04c40001 nt_status_remote_session_limit “an attempt was made to establish a session to a network server, but there are already too many sessions established to that server.” 0 0xc0000197 0x000005df 0x05df0001 nt_status_eventlog_file_changed “the event log file has changed between reads.” 0 0xc0000198 0x0000070f 0x070f0001 nt_status_nologon_interdomain_trust_account “the account used is an interdomain trust your global user account or local user account to access this server.” 0 0xc0000199 0x00000710 0x07100001 nt_status_nologon_workstation_trust_account “the account used is a computer your global user account or local user account to access this server.” 0 0xc000019a 0x00000711 0x07110001 nt_status_nologon_server_trust_account “the account used is an server trust your global user account or local user account to access this server.” 0 0xc000019b 0x00000712 0x07120001 nt_status_domain_trust_inconsistent “the name or security id(sid)of the domain specified is inconsistent with the trust information for that domain.” 0 0xc000019c 0x0000013d 0x001f0003 nt_status_fs_driver_required “nt_status_fs_driver_required” 0 0xc0000202 0x00000572 0x05720001 nt_status_no_user_session_key “there is no user session key for the specified logon session.” 0 0xc0000203 0x0000003b 0x003b0001 nt_status_user_session_deleted “an unexpected network error occurred.” 0 0xc0000204 0x00000717 0x07170001 nt_status_resource_lang_not_found “the specified resource language id cannot be found in the image file.” 0 0xc0000205 0x0000046a 0x046a0001 nt_status_insuff_server_resources “not enough server storage is available to process this command.” 0 0xc0000206 0x000006f8 0x06f80001 nt_status_invalid_buffer_size “the supplied user buffer is not valid for the requested operation.” 0 0xc0000207 0x000004be 0x04be0001 nt_status_invalid_address_component “the format of the specified network name is invalid.” 0 0xc0000208 0x000004be 0x04be0001 nt_status_invalid_address_wildcard “the format of the specified network name is invalid.” 0 0xc0000209 0x00000044 0x00440001 nt_status_too_many_addresses “the name limit for the local computer network adapter card was exceeded.” 0 0xc000020a 0x00000034 0x00340001 nt_status_address_already_exists “a duplicate name exists on the network.” 0 0xc000020b 0x00000040 0x00400001 nt_status_address_closed “the specified network name is no longer available.” 0 0xc000020c 0x00000040 0x00400001 nt_status_connection_disconnected “the specified network name is no longer available.” 0 0xc000020d 0x00000040 0x00400001 nt_status_connection_reset “the specified network name is no longer available.” 0 0xc000020e 0x00000044 0x00440001 nt_status_too_many_nodes “the name limit for the local computer network adapter card was exceeded.” 0 0xc000020f 0x0000003b 0x003b0001 nt_status_transaction_aborted “an unexpected network error occurred.” 0 0xc0000210 0x0000003b 0x003b0001 nt_status_transaction_timed_out “an unexpected network error occurred.” 0 0xc0000211 0x0000003b 0x003b0001 nt_status_transaction_no_release “an unexpected network error occurred.” 0 0xc0000212 0x0000003b 0x003b0001 nt_status_transaction_no_match “an unexpected network error occurred.” 0 0xc0000213 0x0000003b 0x003b0001 nt_status_transaction_responded “an unexpected network error occurred.” 0 0xc0000214 0x0000003b 0x003b0001 nt_status_transaction_invalid_id “an unexpected network error occurred.” 0 0xc0000215 0x0000003b 0x003b0001 nt_status_transaction_invalid_type “an unexpected network error occurred.” 0 0xc0000216 0x00000032 0x00320001 nt_status_not_server_session “the network request is not supported.” 0 0xc0000217 0x00000032 0x00320001 nt_status_not_client_session “the network request is not supported.” 0 0xc0000218 0x0000013d 0x001f0003 nt_status_cannot_load_registry_file “nt_status_cannot_load_registry_file” 0 0xc0000219 0x0000013d 0x001f0003 nt_status_debug_attach_failed “nt_status_debug_attach_failed” 0 0xc000021a 0x0000013d 0x001f0003 nt_status_system_process_terminated “nt_status_system_process_terminated” 0 0xc000021b 0x0000013d 0x001f0003 nt_status_data_not_accepted “nt_status_data_not_accepted” 0 0xc000021c 0x000017e6 0x17e60001 nt_status_no_browser_servers_found “the list of servers for this workgroup is not currently available” 0 0xc000021d 0x0000013d 0x001f0003 nt_status_vdm_hard_error “nt_status_vdm_hard_error” 0 0xc000021e 0x0000013d 0x001f0003 nt_status_driver_cancel_timeout “nt_status_driver_cancel_timeout” 0 0xc000021f 0x0000013d 0x001f0003 nt_status_reply_message_mismatch “nt_status_reply_message_mismatch” 0 0xc0000220 0x0000046c 0x046c0001 nt_status_mapped_alignment “the base address or the file offset specified does not have the proper alignment.” 0 0xc0000221 0x000000c1 0x00c10001 nt_status_image_checksum_mismatch “%1 is not a valid windows nt application.” 0 0xc0000222 0x0000013d 0x001f0003 nt_status_lost_writebehind_data “nt_status_lost_writebehind_data” 0 0xc0000223 0x0000013d 0x001f0003 nt_status_client_server_parameters_invalid “nt_status_client_server_parameters_invalid” 0 0xc0000224 0x00000773 0x07730001 nt_status_password_must_change “the user must change his password before he logs on the first time.” 0 0xc0000225 0x0000013d 0x001f0003 nt_status_not_found “nt_status_not_found” 0 0xc0000226 0x0000013d 0x001f0003 nt_status_not_tiny_stream “nt_status_not_tiny_stream” 0 0xc0000227 0x0000013d 0x001f0003 nt_status_recovery_failure “nt_status_recovery_failure” 0 0xc0000228 0x0000013d 0x001f0003 nt_status_stack_overflow_read “nt_status_stack_overflow_read” 0 0xc0000229 0x0000013d 0x001f0003 nt_status_fail_check “nt_status_fail_check” 0 0xc000022a 0xc000022a 0x022a0001 nt_status_duplicate_objectid “nt_status_duplicate_objectid” 0 0xc000022b 0xc000022b 0x022b0001 nt_status_objectid_exists “nt_status_objectid_exists” 0 0xc000022c 0x0000013d 0x001f0003 nt_status_convert_to_large “nt_status_convert_to_large” 0 0xc000022d 0x0000013d 0x001f0003 nt_status_retry “nt_status_retry” 0 0xc000022e 0x0000013d 0x001f0003 nt_status_found_out_of_scope “nt_status_found_out_of_scope” 0 0xc000022f 0x0000013d 0x001f0003 nt_status_allocate_bucket “nt_status_allocate_bucket” 0 0xc0000230 0x0000013d 0x001f0003 nt_status_propset_not_found “nt_status_propset_not_found” 0 0xc0000231 0x0000013d 0x001f0003 nt_status_marshall_overflow “nt_status_marshall_overflow” 0 0xc0000232 0x0000013d 0x001f0003 nt_status_invalid_variant “nt_status_invalid_variant” 0 0xc0000233 0x00000774 0x07740001 nt_status_domain_controller_not_found “could not find the domain controller for this domain.” 1 0xc0000234 0x00000775 0x07750001 nt_status_account_locked_out “the referenced account is currently locked out and may not be logged on to.” 0 0xc0000235 0x00000006 0x00060001 nt_status_handle_not_closable “the handle is invalid.” 0 0xc0000236 0x000004c9 0x04c90001 nt_status_connection_refused “the remote system refused the network connection.” 0 0xc0000237 0x000004ca 0x04ca0001 nt_status_graceful_disconnect “the network connection was gracefully closed.” 0 0xc0000238 0x000004cb 0x04cb0001 nt_status_address_already_associated “the network transport endpoint already has an address associated with it.” 0 0xc0000239 0x000004cc 0x04cc0001 nt_status_address_not_associated “an address has not yet been associated with the network endpoint.” 0 0xc000023a 0x000004cd 0x04cd0001 nt_status_connection_invalid “an operation was attempted on a non-existent network connection.” 0 0xc000023b 0x000004ce 0x04ce0001 nt_status_connection_active “an invalid operation was attempted on an active network connection.” 0 0xc000023c 0x000004cf 0x04cf0001 nt_status_network_unreachable “the remote network is not reachable by the transport.” 0 0xc000023d 0x000004d0 0x04d00001 nt_status_host_unreachable “the remote system is not reachable by the transport.” 0 0xc000023e 0x000004d1 0x04d10001 nt_status_protocol_unreachable “the remote system does not support the transport protocol.” 0 0xc000023f 0x000004d2 0x04d20001 nt_status_port_unreachable “no service is operating at the destination network endpoint on the remote system.” 0 0xc0000240 0x000004d3 0x04d30001 nt_status_request_aborted “the request was aborted.” 0 0xc0000241 0x000004d4 0x04d40001 nt_status_connection_aborted “the network connection was aborted by the local system.” 0 0xc0000242 0x0000013d 0x001f0003 nt_status_bad_compression_buffer “nt_status_bad_compression_buffer” 0 0xc0000243 0x000004c8 0x04c80001 nt_status_user_mapped_file “the requested operation cannot be performed on a file with a user mapped section open.” 0 0xc0000244 0x0000013d 0x001f0003 nt_status_audit_failed “nt_status_audit_failed” 0 0xc0000245 0x0000013d 0x001f0003 nt_status_timer_resolution_not_set “nt_status_timer_resolution_not_set” 0 0xc0000246 0x000004d6 0x04d60001 nt_status_connection_count_limit “a connection to the server could not be made because the limit on the number of concurrent connections for this account has been reached.” 0 0xc0000247 0x000004d7 0x04d70001 nt_status_login_time_restriction “attempting to login during an unauthorized time of day for this account.” 0 0xc0000248 0x000004d8 0x04d80001 nt_status_login_wksta_restriction “the account is not authorized to login from this station.” 0 0xc0000249 0x000000c1 0x00c10001 nt_status_image_mp_up_mismatch “%1 is not a valid windows nt application.” 0 0xc0000250 0x0000013d 0x001f0003 nt_status_insufficient_logon_info “nt_status_insufficient_logon_info” 0 0xc0000251 0x0000013d 0x001f0003 nt_status_bad_dll_entrypoint “nt_status_bad_dll_entrypoint” 0 0xc0000252 0x0000013d 0x001f0003 nt_status_bad_service_entrypoint “nt_status_bad_service_entrypoint” 0 0xc0000253 0x0000054f 0x054f0001 nt_status_lpc_reply_lost “the security account database contains an internal inconsistency.” 0 0xc0000254 0x0000013d 0x001f0003 nt_status_ip_address_conflict1 “nt_status_ip_address_conflict1” 0 0xc0000255 0x0000013d 0x001f0003 nt_status_ip_address_conflict2 “nt_status_ip_address_conflict2” 0 0xc0000256 0x0000013d 0x001f0003 nt_status_registry_quota_limit “nt_status_registry_quota_limit” 1 0xc0000257 0x000004d0 0x04d00001 nt_status_path_not_covered “the remote system is not reachable by the transport.” 0 0xc0000258 0x0000013d 0x001f0003 nt_status_no_callback_active “nt_status_no_callback_active” 0 0xc0000259 0x00000573 0x05730001 nt_status_license_quota_exceeded “the service being accessed is licensed for a particular number of more connections can be made to the service at this time because there are already as many connections as the service can accept.” 0 0xc000025a 0x0000013d 0x001f0003 nt_status_pwd_too_short “nt_status_pwd_too_short” 0 0xc000025b 0x0000013d 0x001f0003 nt_status_pwd_too_recent “nt_status_pwd_too_recent” 0 0xc000025c 0x0000013d 0x001f0003 nt_status_pwd_history_conflict “nt_status_pwd_history_conflict” 0 0xc000025e 0x00000422 0x04220001 nt_status_plugplay_no_device “the specified service is disabled and cannot be started.” 0 0xc000025f 0x0000013d 0x001f0003 nt_status_unsupported_compression “nt_status_unsupported_compression” 0 0xc0000260 0x0000013d 0x001f0003 nt_status_invalid_hw_profile “nt_status_invalid_hw_profile” 0 0xc0000261 0x0000013d 0x001f0003 nt_status_invalid_plugplay_device_path “nt_status_invalid_plugplay_device_path” 0 0xc0000262 0x000000b6 0x00b60001 nt_status_driver_ordinal_not_found “the operating system cannot run %1.” 0 0xc0000263 0x0000007f 0x007f0001 nt_status_driver_entrypoint_not_found “the specified procedure could not be found.” 0 0xc0000264 0x00000120 0x01200001 nt_status_resource_not_owned “attempt to release mutex not owned by caller.” 0 0xc0000265 0x00000476 0x04760001 nt_status_too_many_links “an attempt was made to create more links on a file than the file system supports.” 0 0xc0000266 0x0000013d 0x001f0003 nt_status_quota_list_inconsistent “nt_status_quota_list_inconsistent” 0 0xc0000267 0x0000013d 0x001f0003 nt_status_file_is_offline “nt_status_file_is_offline” 0 0xc0000275 0x0000013d 0x001f0003 nt_status_not_a_reparse_point “nt_status_not_a_reparse_point” 0
0xc0000ede 0x0000013d 0x001f0003nt_status_no_such_job “nt_status_no_such_job”